FAQs

What does the Customised firmware allow me to do?

Add extra or enhanced features to your Humax HDR FOX T2 and HD FOX T2, Some features will add 'Every Day' enhancements such as Add to recording schedule remotely, Add more sites to the Humax Portal and Auto Unprotection of Hi-Def programs, While other utilities are for advanced developers. An overview of the Custom Firmware features are listed HERE

What will happen if / when Humax transmits an Over-the-air (OTA) update?

The customised software will be overwritten. Any services installed by the customised software will become dormant. Any files on the hard disk that were created with the customised software will remain in place and will be accessible when a new version of the customised software is applied on top of the OTA version.

How can I compile software to run on the Humax?

Have a look at the Compile Software for the Humax and Create Packages HOW-TOs.

What Does this EPG Icon Mean?

What Does this Front Panel Icon Mean?

1. TV Mode	2. Radio Mode	3. Full Res. (1080p) v-format	4. High Definition
5. Dolby Digtial Source	6. Dolby Digital Plus	7. Dolby Digital ProLogic?	8. USB Device connected
9. Recording	10. Play (during re-play)	11. Pause	12. Schedule timer
13. Wifi connected	14. HDMI CEC?	15. E-Mail?	16. Hard Disk Free Space

HIDE ** = Not Used

Where is the Remote Control Sensor?

It is quite difficult to see the Remote Control Sensor on the HDR Fox T2, Keeping this area clear will improve Remote Control sensitivity

Why is My Remote Flashing all the Mode LEDS ?

If your Remote Flashes all four 'Mode' LEDS in sequence when you press the green power button, It is indicating that the battery level is low

How do avoid Remote Macro Problems

Many ‘All-in-One’ / Harmony type remotes Controls have a ‘Macro’ facility, where a single key press will send multiple commands to carry out a series of operations, However problems can occur when the original remote control uses a single button to toggle power On / Off functions because different pieces of equipment may already be in the desired state, Sony and several other Makers get around this by having separate buttons for On and Off, however the Humax Remote don’t have this.

Solution

Send ‘000’ to the Humax HDR T2 as a ‘Turn On Only’ signal, thereby getting around the possible ‘out of synchronisation’ problem. It has been reported that on some remotes a single 'Zero' for 3 seconds works better than 'Zero, Zero, zero'

How do I remove Channel Duplicates?

Background

If you have channel numbers between 800 and 899 they need to be removed, these channels are duplicates and have been allocated their 800+ number by the Humax, It as been reported that signals from duplicate channels can stop Accurate Recording from functioning correctly, also the Humax does not always allocate the strongest signal channel first, this results in poor reception on the ‘Main’ channels and better reception on the unused 800’s channels.

Perform a Manual Re-Scan

Note:- The following procedure will remove your recording schedule (but not recordings) and also your Favourites list so make a note of them before carrying out a re-scan.

• Determine your strongest Local Freeview channel numbers by entering your postcode and selecting detailed view HERE
• Make a note of the 6 'Main' MUXs you need to keep (rejecting weaker signals)
• Start an auto. channel re-scan e.g. Menu >> Settings >> Installation >> Automatic Search
• Stop the auto. re-scan before any channels are found (This will clear all old channels)
• Using the Noted 6 Mux. Channel numbers perform a Manual channel scan e.g. Menu >> Settings >> Installation >> Manual Search
• NOTE Ensure that 'Network Search' is set to off
• The Hi Def. MUX requires the DVB-T2 transmission type all others require DVB-T
• You will now have all the TV channels contained within the 6 MUXs with no duplicates

Which WiFi Dongle?

There are a few to choose from including Humax's own, It has been reported that to work with the Humax, Dongles must have the RALINK 3070 chipset

NOTES

• It has been reported that channels 1 to 4 can't be used with the Humax
• There is a list of Ralink 3070 devices HERE (Chip Used = RT3070) , Caution, The items in this link have not been proved to work on the Humax

The following are reported to work on the Humax :-

• Trixes WiFi Wireless USB Adaptor Fast 150MBPS from Play.com
• Logilink WL0049A
• Tenda W311u+ 150Mbps from Amazon
• LG PW-DN427
• Edimax - EW - 7711 Models 150MBPS (*** Some Models only See below)

The following are reported NOT to work on the Humax :-

• Edimax - EW - 7612
• Belkin - F5D8053 - N
• Texet - WA3070-06 - N
• Getnet - GN-621U aka Realtek RTL8191SU
• Netgear - WPN111GE
• Edimax - EW - 7711 Models 150MBPS (*** versions with Win8 logo on box are reported NOT to work with the Humax)

How do I reset my Web-If Password

If you have forgotten your Web-If password you can reset it by accessing the Humax Telnet screen.

The Telnet Menu (Option 2) can do this, If the Telnet Menu is turned off, you can reset it by entering the following Telnet command line :-

diag removepw

How do I restart the Web-If GUI?

If you have a problem the Web-If Graphical User Interface, it can be re-started from Telnet as follows :-

service stop mongoose

service start mongoose

How do I set the MTU on my Humax?

If you get error messages like this "Resource temporarily unavailable.Error retrieving package list from the Internet. Please check your connection and try again." you may need to change your Maximum Transmission Unit (MTU) size in order to prevent packets being fragmented, If you need to fix the MTU on your humax, it can be achieved via Telnet as follows :-

• Create a start-up script called S22mtu and place it in the /mod/etc/init.d folder

echo ifconfig eth0 mtu 1400 > /mod/etc/init.d/S22mtu

• Change the permissions on this new script to allow it to be executed

chmod 755 /mod/etc/init.d/S22mtu

• The new script will now auto-run each time the Humax is booted and will set MTU = 1400

Check for notification of any fragmentation during transmission of a given packet size by using ping, e.g. :-

ping x.x.x.x -s 1500 . . . from a Humax command prompt or

ping x.x.x.x -l 1500 . . . from a windows cmd prompt

ping x.x.x.x -l 3000 -f . . . also from a windows cmd prompt

How do I view 2.35:1 Content?

settings > preferences > video > change screen ratio to 4:3 and display format to letterbox 16:9

Why is my Humax Half Awake?

The Humax can be in 3 distinct powered states, they are :-

1. Standby = hard disk not spinning, No TV output, DLNA Server inactive, LAN inactive, No USB power
2. Half Awake = hard disk spinning, No TV output, DLNA Server inactive, LAN active, USB power on
3. Awake = hard disk spinning, TV output, DLNA Server running, LAN active, USB power

The Humax is expected to be in the Half awake state while :-

• Recording from standby
• Waiting to record from standby (15 Minutes)
• Looking for OTA updates at 4:30am daily
• Immediately after initial power on

The Humax can also unexpectedly enter the half awake state due to :-

• Setting an Auto Off timer without a matching Auto On timer
• The presents of corrupted recordings sometimes with move/copy options greyed out
• The *Deleting message being permanently displayed

Note Enabling humaxtv debugging by running debugtv in Web-If >> Diagnostics will create a humaxtv.log file, examining this file with Web-If >> Diagnostics >> View Log File >> humaxtv.log while trying to place the Humax in standby can produce an error message showing why the Humax can't enter standby mode

How Do I Test My HDD?

Humax have build a Hard Disk Drive test routine into version 1.02.28 of it's software, this routine will only test the internal Hard disk of the HDR and is initiated as follows :- Menu >> Settings >> System >> Data Storage >> HDD Test. Also Custom Firmware 2.12 has a built-in HDD utility called Fix-Disk See Notes HERE

What format should be used for a USB HDD

If you want to use a USB Hard disk drive on you Humax there are several formats that can be used, however there is no perfect solution because they all have pros and cons that need to be considered e.g. :-

Format	Pros	Cons
Fat32	Both humax and PC will read/write	There is a 4GB Maximum file size
NTFS	No 4GB file limit	Humax will read but not write (Note 1)
EXT3 (Note 2)	Humax will read/write with no file limit	A PC won't read/write from default (Note 3)
exFAT	N/A (See Cons)	Not supported by Humax (Note 4)

Notes :-

1. The custom Firmware can add NTFS reading to the Humax Link Here
2. USB Flash drives should not be formatted in EXT3 (Use EXT2 instead)
3. A PC can read EXT3/EXT2 with an extra program (Link Here)
4. Support for the ExFAT format can added using the Custom firmware package ExFAT Builder
5. The Humax will format a USB hard disk for you (EXT3 is the only option)
6. A USB drive used for software upgrade MUST be formatted in FAT32
7. When the HD-Fox T2 uses USB flash with Custom Firmware it MUST be formatted in EXT2
8. Flash drives below 32GB can't be used by the Humax for recording

How do I convert a drive to EXT2?

If you are using a USB Flash device to record to ( HD-FOX T2 only <32GB) or as a backup device, the Humax will only use EXT3 as a format mode, due to journalling it is recommended that a Flash device be converted to the EXT2 format to prolong it’s life, here is the procedure to use after a Humax format. NOTE :- tune2fs is part of the Custom Firmware package E2fs_Progs and is also built-in to Custom Firmware Version 2.12 and later.

Telnet into the Humax (Notes Here) and select option 1 e.g. Restart into maintenance mode from the telnet menu, if the telnet menu is not displayed, create the maintenance.boot (details below) :-

touch /var/lib/humaxtv/mod/maintenance.boot
reboot

If it is an HD then presumably the disk will be /dev/sda but it is best to make sure using Fdisk, this should show the size of the disk and the available partitions e.g. for an 8GB USB Flash device

fdisk -l /dev/sda

Disk /dev/sda: 8004 MB, 8004304896 bytes
35 heads, 21 sectors/track, 21269 cylinders
Units = cylinders of 735 * 512 = 376320 bytes
 
  Device Boot      Start        End      Blocks  Id System
/dev/sda1              1      21270    7816688  83 Linux

Unmount the partition if already mounted with

umount /dev/sda1

convert from ext3 to ext2 with :-

/mod/sbin/tune2fs -O ^has_journal /dev/sda1

or convert from ext2 to ext3 with :-

/mod/sbin/tune2fs -j /dev/sda1

When finished type 'reboot'

What Hardware / Software clashes with the Humax?

Below is a list of Hardware / Software know to cause problems with the Humax is some way

Hardware / Software	Problem Details
Twonky Ver 7 (Ver.6 O.K.)	A network conflict when Content Share = on causes constant reboot
Cyberlink PowerDVD Ver. 11 & 12	A network conflict when Content Share = on causes constant reboot

Why has my Humax's IP address changed?

Your Humax's IP address in Menu >> Settings >> System >> Internet Settings >> Configure LAN can change for several reasons depending on whether it is setup for DHCP or Manual operation. In DHCP mode you can expect the last set of digits to be allocated by your router over a certain range, so if your router is set to 192.168.123.xxx, any address in the range 192.168.123.001 to 192.168.123.254 can be expected, A failed DHCP allocation can result in an IP in the range 169.254.x.x being allocated. In Manual mode you would not expect your Humax's IP address to change, however if an unexpected address starting with 192.2.x.x is displayed the Humax has reset to factory default for some reason

Which DNS server should I be using?

There are several places on the internet that provide DNS look-up services, however users have reported 8.8.8.8 causes problems on the Humax, 208.67.222.222 has been reported to be more reliable

Why are sidecar files missing after a copy

Accompanying the main TS video file on the Humax are a group of small ancillary files referred to as 'sidecar' files, these files carry extra data that the Humax uses for Thumbnail pictures, bookmarks etc. When recordings are copied using the remote control the sidecar files (i.e. hmt, thm and nts) should also be copied if they exist, before the Humax copies the TS file it checks there is sufficient free space in the destination drive, after copying the TS file, another check is carried but this will fail and the sidecar files won't be copied if the free space is smaller than the TS file, even though the sidecar files are very much smaller than the TS file

How Can I fix / Get around problem XYZ?

You could have a look at our Fixes & Work Arounds Page

Still no luck. Where can I ask for help?

Visit the hummy.tv forums for more help. They're a friendly bunch!