Difference between revisions of "WebIf Remote Controller"

From hummy.tv Wiki
Jump to: navigation, search
(Macros)
Line 1: Line 1:
__NOTOC__
+
 
 
[[File:ir.png|500px|thumb|right]]
 
[[File:ir.png|500px|thumb|right]]
  

Revision as of 00:41, 6 January 2015

Ir.png

The IR package adds a fully functioning Remote Controller to the Web-Interface, It can be installed from the Web-If >> Package Management page and once installed a ‘Remote’ icon will be added to the Web-If Main screen


Channel Shortcuts

Change

  • allow quick selection of a new TV/Radio station from a list


Customise

  • Add/Remove Favourite quick select channel Icons
  • Block remote control mode change icons on TV
  • Swap INFO and LIST commands
  • Disable Volume Control
  • Use Custom Map File

The custom map file must be named /mod/boot/ir3.map and be of the form <original keycode>:<replacement keycode>:<comment>. Here are some examples including a macro on the Subtitle button

0e:43:MENU -> INFO
1f::VOL+ disabled
40::VOL- disabled
4d:43:LIST becomes INFO
43:4d:INFO becomes LIST
46:40,40,40,f2,c,3,a:Subtitle button = VOL-, VOL-, VOL-, WAIT 2 seconds, 0, 1, 8

Notes

  1. Use ir -l to show code mappings.
  2. Delays can be added to macros by using fX where X is the number of seconds to wait as a hex digit, so f1 for a second, f9 for 9 seconds, fb for 11 seconds up to fe for 14 seconds
  3. Web-If >> Diagnostic >> File Editor >> /mod/boot/ir3.map shows the default code mapping


  • Select Remote Control Mode (1-6)

Note:- this setting will only take effect after a reboot and will only change the 'ir' Mode, it will not change the Humax Operating Mode (See Below) or the Remote Control Mode

The Customise options are also available in Web-If >> Settings >> Remote Control Settings,

Macros

  • record a sequence of key strokes, to be replayed with a single 'click'
  • A Macro named root will automatically be run when the Humax is taken out of standby
  • Macro sequences are stored here :- /mod/etc/webif.db, macros can be transferred to another unit by copying this file

Selecting Record a New Macro will display a Name Box and some delay keys to create a pause in the sequence

History

Displays a clearable list of commands sent

Ir-mob.png

Mobile Version

There is a mobile version of the Web-If Remote Controller that is more suited to the ‘small screen’. If the IP address of your humax is 10.0.0.200 then the mobile version’s address would be :- http://10.0.0.200/plugin/ir/m/

There are three selectable screens that display Remote - Favs - Macros


Command Line Options

The IR package is also controllable as a command line via Telnet, here are some examples :-


humax# status Watching 7: BBC THREE - This Is BBC Three (05:30 - 18:58) [48%]

ir SEVEN DELAY1 TWO OK

SEVEN (0x9)

DELAY1 [delay between 1-99 Seconds]

TWO (0x4)

OK (0x13)

humax# status Watching 72: CITV - Horrid Henry (12:00 - 12:15) [13%]


Remote Control Mode Setting (Humax)

From the command line enable the TV screen Mode Display / Set function with:-

ir CURMODE MODE

To set the Humax to Remote Control Mode 1 from the command line :-

ir CURMODE MODE DELAY2 MODE1

This will change the Expected Mode on the Humax's Operating system only, it will not change the Mode on the Remote Control or the Custom Firmware's ir package itself

To change the Mode on the Remote Control see link HERE

To change the Custom Firmware ir Mode see Customise >> Select Remote Control Mode above


NOTE


The Web-If Remote Controller can only control your Humax, the 'TV' 'DVD' and 'AUDIO' mode buttons will not control other equipment