Difference between revisions of "Remote Disassembled"

From hummy.tv Wiki
Jump to: navigation, search
Line 2: Line 2:
 
[[File:rem01.png|400px|thumb|right|'''Photo 2 - First 2 lugs 'popped'''']]
 
[[File:rem01.png|400px|thumb|right|'''Photo 2 - First 2 lugs 'popped'''']]
 
[[File:rem02.png|400px|thumb|right|'''Photo 3 - Battery end lugs''']]
 
[[File:rem02.png|400px|thumb|right|'''Photo 3 - Battery end lugs''']]
[[File:remote-pad.png|400px|thumb|right|'''Photo 10 - Before and after new pads''']]
+
[[File:remote-pad.png|400px|thumb|right|'''Photo 10 - Before and after new 'waffle' pads''']]
 +
 
 +
 
 +
 
 
'''Background'''
 
'''Background'''
  
Line 8: Line 11:
  
 
You may also be just curious as to what is inside, Users have been known to disassemble their products for this very reason
 
You may also be just curious as to what is inside, Users have been known to disassemble their products for this very reason
 +
 +
  
 
'''Warning'''
 
'''Warning'''
  
 
The RM-F04 Remote is not held together with screws, It is ‘Snapped’ together which make it quite difficult to take apart, It is not recommended that you disassemble  your Remote unless there is a very good reason, e.g. it has stopped working. There is a real possibility that the case could be damaged
 
The RM-F04 Remote is not held together with screws, It is ‘Snapped’ together which make it quite difficult to take apart, It is not recommended that you disassemble  your Remote unless there is a very good reason, e.g. it has stopped working. There is a real possibility that the case could be damaged
 +
 +
  
 
'''Disassembly'''
 
'''Disassembly'''
Line 31: Line 38:
  
  
 +
'''Repair'''
  
 +
As remotes get older the 'Waffles (Photo 9)' tend to loose their conductivity and no amount of cleaning will restore this, one solution is to attach aluminium foil to double sided sticky tape and then, using a paper punch, make circular sticky pads that can be stuck on top of the waffle as in Photo 10
  
  
  
 +
'''Re-Assembly'''
  
 +
Clip PCB back into place, Then Hook the two halves of the case back together at the non Battery end and then snap all other lugs into place
  
  
'''Repair'''
 
 
As remotes get older the 'Waffles (Photo 9)' tend to loose their conductivity and no amount of cleaning will restore this, one solution is to attach aluminium foil to double sided sticky tape and then, using a paper punch, make circular sticky pads that can be stuck on top of the waffle as in Photo 10
 
 
 
  
'''Re-Assembly'''
 
  
Clip PCB back into place, Then Hook the two halves of the case back together at the non Battery end and then snap all other lugs into place
 
  
 
{| border="1"
 
{| border="1"
Line 59: Line 63:
 
![[File:rem09.png|400px|thumb|right|Photo 9 - Button 'Waffles']]
 
![[File:rem09.png|400px|thumb|right|Photo 9 - Button 'Waffles']]
 
|-
 
|-
![[File:rem06.png|400px|thumb|right|Photo 10 - Full PCB]]
+
![[File:rem06.png|400px|thumb|right|Photo 11 - Full PCB]]
![[File:rem08.png|400px|thumb|right|Photo 11 - Rear of Buttons]]
+
![[File:rem08.png|400px|thumb|right|Photo 12 - Rear of Buttons]]
 
|-
 
|-
![[File:rem12.png|400px|thumb|right|Photo 12 - Battery side of PCB]]
+
![[File:rem12.png|400px|thumb|right|Photo 13 - Battery side of PCB]]
![[File:rem11.png|400px|thumb|right|Photo 13 - Top side of Buttons]]
+
![[File:rem11.png|400px|thumb|right|Photo 14 - Top side of Buttons]]
 
|-
 
|-
![[File:rem13.png|400px|thumb|right|Photo 14 - Back of Case (Inner)]]
+
![[File:rem13.png|400px|thumb|right|Photo 15 - Back of Case (Inner)]]
![[File:rem10.png|400px|thumb|right|Photo 15 - Top of case (Inner)]]
+
![[File:rem10.png|400px|thumb|right|Photo 16 - Top of case (Inner)]]
 
|}
 
|}

Revision as of 14:12, 30 December 2012

<<<--3------------------2-----------------Start Here
Photo 2 - First 2 lugs 'popped'
Photo 3 - Battery end lugs
Photo 10 - Before and after new 'waffle' pads


Background

The RM-F04 Remote Control supplied with the Humax HDR FOX T2 and Humax HD FOX T2 may need disassembling for various reasons, The main reason being that the Remote becomes unresponsive to key presses, even with new batteries.

You may also be just curious as to what is inside, Users have been known to disassemble their products for this very reason


Warning

The RM-F04 Remote is not held together with screws, It is ‘Snapped’ together which make it quite difficult to take apart, It is not recommended that you disassemble your Remote unless there is a very good reason, e.g. it has stopped working. There is a real possibility that the case could be damaged


Disassembly

Remove the batteries and replace the cover, The case is held together with 12 ‘snap fit lug + Barbs’ (Photos 6 + 7), 5 on each long side and 2 at the battery end, The locations of the 5 side lugs are shown in Photo 1. The only tools required for the disassembly are two thin metal objects, I used two No. 22 scalpel blades (0.4mm thick), Although it is possible to use a thicker tool it will inevitably damage the case as the gap between the two halves of the case is very small.

Locate a centre lug on a long side using photo 1 and insert a scalpel blade at that point, leaver the bottom half of the case outwards and a ‘click’ should be heard as the barb disengages, Keep this scalpel in place while you work on the next lug towards the battery end, Do the same procedure on the second lug, Photo 2 shows two blades in place, It should be safe to remove the blades now.

Disengage the last side lug at the battery end, Now locate the battery end lug (Photo 3) nearest to the lugs already opened and open it, Followed by the second battery and lug.

Work up the other side of the case to the middle lug prizing the case apart as you go, Remove the last 4 lugs, NOTE there are no lugs on the other end but there is a hinge arrangement

With buttons facing down, remove the back of the remote, Remove the Printed Circuit Board by gently levering it away from the corner plastic lug (Photo 4)

Clean the PCB with Methylated Spirits and a cotton bud, (do not use an abrasive), the areas of interest are the ‘fingers’ as shown on PCB detail Photo 8

Next use Methylated Spirits and a cotton bud (do not use an abrasive), to clean the round ‘Waffles’ on the underside of the buttons Photo 9


Repair

As remotes get older the 'Waffles (Photo 9)' tend to loose their conductivity and no amount of cleaning will restore this, one solution is to attach aluminium foil to double sided sticky tape and then, using a paper punch, make circular sticky pads that can be stuck on top of the waffle as in Photo 10


Re-Assembly

Clip PCB back into place, Then Hook the two halves of the case back together at the non Battery end and then snap all other lugs into place



Photo 4 - PCB under lug
Photo 5 - Tools
Photo 6 - 'Lug'
Photo 7 - 'Barb'
Photo 8 - PCB Fingers
Photo 9 - Button 'Waffles'
Photo 11 - Full PCB
Photo 12 - Rear of Buttons
Photo 13 - Battery side of PCB
Photo 14 - Top side of Buttons
Photo 15 - Back of Case (Inner)
Photo 16 - Top of case (Inner)