Difference between revisions of "Maintenance Mode"

From hummy.tv Wiki
Jump to: navigation, search
Line 13: Line 13:
 
==Enter Telnet Menu==
 
==Enter Telnet Menu==
  
The first stage in entering Maintenance Mode is to access the Humax via Telnet e.g. :-
+
The first stage in entering Maintenance Mode is to access the Humax via [[Custom_Firmware_Package_Notes#Telnet|'''Telnet''']]  e.g. :-
  
 
Enter 0000 <return> for system PIN
 
Enter 0000 <return> for system PIN
Line 37: Line 37:
 
</pre>
 
</pre>
  
If the Telnet Menu is not present, Maintenance mode can be initiated by using [[Custom_Firmware_Package_Notes#Telnet|'''Telnet''']]
+
If the Telnet Menu is not present, Maintenance mode can be initiated by using [[Custom_Firmware_Package_Notes#Telnet|'''Telnet''']] command line
  
 
<span style="background:#FFFF00"> touch /var/lib/humaxtv/mod/maintenance.boot </span>
 
<span style="background:#FFFF00"> touch /var/lib/humaxtv/mod/maintenance.boot </span>
Line 61: Line 61:
 
</pre>
 
</pre>
  
If the Maintenance Mode Menu is not present, Fix-Disk mode can be initiated by Telnetting
+
If the Maintenance Mode Menu is not present, Fix-Disk mode can be initiated by using [[Custom_Firmware_Package_Notes#Telnet|'''Telnet''']] command line
  
 
<span style="background:#FFFF00"> fix-disk </span>
 
<span style="background:#FFFF00"> fix-disk </span>

Revision as of 19:05, 3 December 2012

Note Note: If you are planning to use maintenance mode, it is recommended that you first upgrade to Customised Firmware version 2.14 or above.

Background

Maintenance Mode has been created to enable the Humax to carry out special functions that can’t be run in normal mode, When this mode is running there will be no TV Tuner, TV Recording or Custom Firmware Graphical User Interface (GUI), on Custom Firmware Version 2.13 and later, Maintenance Mode is indicated on the Humax display as follows :- 'MAINTENANCE' on HDR and 'UtiL' on HD)

Access to this mode is via Telnet - Command line only.

When the Custom Firmware boots up it will look for a special file, If it finds this file, the Firmware will boot into Maintenance Mode and then delete the file, If the file is not found the Firmware will boot into the normal Custom Firmware


Enter Telnet Menu

The first stage in entering Maintenance Mode is to access the Humax via Telnet e.g. :-

Enter 0000 <return> for system PIN

Menu Version 1.02
Enter System PIN :

/-----------------------\
| T E L N E T  M E N U  |
\-----------------------/

[ Humax HDR-Fox T2 (humax)1.02.29 / 2.14 ]

   1 - Restart into maintenance Mode.
   2 - Remove Web interface Password. 
Stat - Show what the box is currently doing.
   x - Exit and close connection.
diag - Run a diagnostic
 cli - Exit to system command line (Advanced users)

Please select option :

If the Telnet Menu is not present, Maintenance mode can be initiated by using Telnet command line

touch /var/lib/humaxtv/mod/maintenance.boot

reboot


Enter Maintenance Mode

Select the first Item in this Menu e.g. 1 - Restart into maintenance Mode, The Humax will close the current Telnet session and reboot and display 'Maintenance Mode' after a short delay, the following Menu will then be displayed :-

   /-----------------------------------------\
   | M A I N T E N A N C E  M O D E  M E N U |
   \-----------------------------------------/

  [Humax HDR-Fox T2 (humax) 1.02.29/2.14]

   1 - Check and repair hard disk (fix-disk)
   2 - Clear persistent EPG data.
   x - Leave maintenance mode (Humax will restart).
diag - Run a diagnostic.
 cli - Exit to system Command line (Advanced users).

If the Maintenance Mode Menu is not present, Fix-Disk mode can be initiated by using Telnet command line

fix-disk

Fix-Disk

Select 1) from the Maintenance Mode Menu to initiate the Fix-Disk utility :-

Checking partition /dev/sda3...
Checking partition /dev/sda1...
Creating swap file...
Checking partition /dev/sda2...
Are you having problems with a delete loop [Y/N]?

Note:- If the Humax is constantly displaying the word 'Deleting', answer Yes, if not answer No.


Maintenance Mode Notes

While in Maintenance Mode Only Telnet is functional, The following Notes are Valid for the HDR-Fox T2:-

  • Disk are shown as /dev/sda, /dev/sdb, etc
  • An external HDD found on boot will be /dev/sda and the internal HDD will be /dev/sdb
  • An External HDD connected after boot will be /dev/sdb and the internal HDD will be /dev/sda
  • Partitions on those disks are /dev/sda1, /dev/sda2 etc
  • fdisk -lu HIDE Will display Disks and their Partitions
  • df -h HIDE Will display Mounted Disks


Exit Maintenance Mode

To exit Maintenance Mode, Selext 'x' from the Telmet Menu or Telnet the following :-

reboot

What is Maintenance Mode for ?

At present, it is used for checking the HDR internal disk file system and formatting USB hard disks up to 2TB (The standard Humax format only works up to 1TB)

Run a file system check on the Internal Hard Disk Drive

See notes on the fix-disk utility

Format a WD Elements 2TB USB external Hard Disk

Full Details Here

These are some extracted notes for drive = /dev/sda1 :-

  • Ensure you are formatting the correct drive e.g. /dev/sda1 or /dev/sda2
  • unmount drive (if Mounted already mounted) with e.g. umount /dev/sda1
  • Partition the disk with using fdisk -u /dev/sda1 then p to display current
  • d to delect current
  • n to create primary partition
  • p to select primary partition
  • Partition no = 1 First Sector = 2048 last sector = default
  • p to display new selection e.g. Disk /dev/sda: 2000.3 GB, 2000396746752 bytes
  • w to write new partition and exit fdisk
  • Format new partition with mkfs.ext3 /dev/sda1
  • format will will take about 20 minutes for a 2TB disk