Difference between revisions of "Install Modified Firmware"

From hummy.tv Wiki
Jump to: navigation, search
(Created page with "The procedure for upgrading Humax software, (both original and Modified) is as follows :- - Power OFF the product using the rear ON/OFF switch - Download the software and save ...")
 
 
(55 intermediate revisions by 5 users not shown)
Line 1: Line 1:
The procedure for upgrading Humax software, (both original and Modified) is as follows :-
+
The procedure for upgrading Humax software, both original and customised (Modified) is detailed below.
  
- Power OFF the product using the rear ON/OFF switch
+
==HDR Fox T2==
  
- Download the software and save on a USB Pen drive
+
* [[Firmware_Downloads | '''Download the firmware''']] and, if it is a zip file, extract it
 +
* Ensure the resulting file is named ''HDR_FOX_T2_Upgrade.hdf''
 +
* Place the file in the root of a FAT32 formatted USB Flash / disk Drive *
 +
* Put the unit into standby using the remote or the central 'big button' on the Unit
 +
* Make sure that the unit has completely shut down by listening for the hard drive to power down (accompanied by a click)
 +
* Remove all USB devices
 +
* Plug the USB Flash Device containing the HDF file into a USB port
 +
* Turn on the TV and switch to the Humax input
 +
* Start up the Humax using the big button on the front of the unit ('''not''' by using the remote control)
 +
* The software update should begin automatically and the progress shown on the TV screen
 +
* The initial ''download'' is very quick and then programming takes 2-3 minutes
 +
* Pauses in the percentage time bar are quite normal
 +
* If after waiting 15 minutes the progress bar has not completed, power the unit off and back on using the rear switch to re-strart the process
 +
* A list of possible Error codes that may be displayed are detailed [[Firmware Error Codes|'''HERE''']]
 +
* When the update is complete End will appear on the front display and ''Success Downloading!'' will appear on the TV
 +
* Unplug the USB Flash Device containing the HDR_FOX_T2_Upgrade.hdf file
 +
* re-connect any other USB devices e.g. Wi-Fi adadper, Hard disk Drives etc. (ensure that the HDF file is not present)
 +
* Press the big button on the front again to restart with the new firmware
  
- Make sure the filename is hdr_fox_t2_upgrade.hdf
 
  
- Insert the USB Pen drive directly into the front or rear USB port
+
'''To Install a Full Web Interface Continue''' [[Install_Full_Web_Interface | '''HERE''']]
  
- Power ON the product using the rear ON/OFF switch
+
==HD Fox T2==
  
- The download should start and the download progress should appear on the TV set
+
{{note|The HD Fox T2 requires a USB Flash / Disk Drive with a minimum of 2GB to be connected when operating with Custom Firmware otherwise it will not be possible to install additional software packages, Flash devices must be formatted in EXT2 using a P.C. program such as GParted “Live” CD, Hard Disk devices can be formatted in EXT3 by the HD FOX T2}}
 +
* [[Firmware_Downloads | '''Download the firmware''']] and, if it is a zip file, extract it
 +
* Ensure the resulting file is named ''HD_FOX_T2_Upgrade.hdf''
 +
* Place the file in the root of a FAT32 formatted USB Flash / disk Drive *
 +
* Put the unit into standby using the remote, or power button on the front
 +
* Plug the USB Flash device into the USB port
 +
* Turn on the TV and switch to the Humax input
 +
* Press and hold down the power button on the front until you see the software update begin, and the progress is shown on the TV screen
 +
* The initial ''download'' is very quick and then programming takes 2-3 minutes
 +
* Pauses in the percentage time bar are quite normal
 +
* A list of possible Error codes that may be displayed are detailed [[Firmware Error Codes|'''HERE''']]
 +
* When the update is complete End will appear on the front display and ''Success Downloading!'' will appear on the TV
 +
* Unplug the USB Flash Device and delete the HD_FOX_T2_Upgrade.hdf file
 +
* Reconnect a USB Flash / Hard Disk drive formatted in EXT2 / EXT3 (See Note above)
 +
* Press the power button on the front to restart with the new firmware
  
- When the update is complete End will appear on the front display, "Download Successful will appear on the TV.
 
  
- Remove USB Pen and press standby
+
'''To Install a Full Web Interface Continue''' [[Install_Full_Web_Interface | '''HERE''']]
  
Notes:
 
  
During the update process DO NOT power off the product
 
  
USB Pen must be formatted in FAT32
+
{{note|
 
+
Some USB Flash / Disk Drives* are reported not to work, The reason for this is not fully understood, However the following Tips are known to help :-
The software must be on the root directory of the USB Pen drive (e.g. not in a sub-folder)
+
* Ensure no other USB devices are connected
 
+
* Do not use a USB extender cable
Try the other USB port if the first doesn't start upgrade
+
* Removing all other files / full-formatting can prevent file fragmentation
 
+
* Try both USB ports (HDR)
Not all USB Pens will be recognised, try a different USB Pen
+
* Smaller capacity drives seem to work more successfully than large ones
 +
* Last Resort, Try a different USB Flash Drive
 +
}}

Latest revision as of 16:18, 8 July 2020

The procedure for upgrading Humax software, both original and customised (Modified) is detailed below.

HDR Fox T2

  • Download the firmware and, if it is a zip file, extract it
  • Ensure the resulting file is named HDR_FOX_T2_Upgrade.hdf
  • Place the file in the root of a FAT32 formatted USB Flash / disk Drive *
  • Put the unit into standby using the remote or the central 'big button' on the Unit
  • Make sure that the unit has completely shut down by listening for the hard drive to power down (accompanied by a click)
  • Remove all USB devices
  • Plug the USB Flash Device containing the HDF file into a USB port
  • Turn on the TV and switch to the Humax input
  • Start up the Humax using the big button on the front of the unit (not by using the remote control)
  • The software update should begin automatically and the progress shown on the TV screen
  • The initial download is very quick and then programming takes 2-3 minutes
  • Pauses in the percentage time bar are quite normal
  • If after waiting 15 minutes the progress bar has not completed, power the unit off and back on using the rear switch to re-strart the process
  • A list of possible Error codes that may be displayed are detailed HERE
  • When the update is complete End will appear on the front display and Success Downloading! will appear on the TV
  • Unplug the USB Flash Device containing the HDR_FOX_T2_Upgrade.hdf file
  • re-connect any other USB devices e.g. Wi-Fi adadper, Hard disk Drives etc. (ensure that the HDF file is not present)
  • Press the big button on the front again to restart with the new firmware


To Install a Full Web Interface Continue HERE

HD Fox T2

Note Note: The HD Fox T2 requires a USB Flash / Disk Drive with a minimum of 2GB to be connected when operating with Custom Firmware otherwise it will not be possible to install additional software packages, Flash devices must be formatted in EXT2 using a P.C. program such as GParted “Live” CD, Hard Disk devices can be formatted in EXT3 by the HD FOX T2

  • Download the firmware and, if it is a zip file, extract it
  • Ensure the resulting file is named HD_FOX_T2_Upgrade.hdf
  • Place the file in the root of a FAT32 formatted USB Flash / disk Drive *
  • Put the unit into standby using the remote, or power button on the front
  • Plug the USB Flash device into the USB port
  • Turn on the TV and switch to the Humax input
  • Press and hold down the power button on the front until you see the software update begin, and the progress is shown on the TV screen
  • The initial download is very quick and then programming takes 2-3 minutes
  • Pauses in the percentage time bar are quite normal
  • A list of possible Error codes that may be displayed are detailed HERE
  • When the update is complete End will appear on the front display and Success Downloading! will appear on the TV
  • Unplug the USB Flash Device and delete the HD_FOX_T2_Upgrade.hdf file
  • Reconnect a USB Flash / Hard Disk drive formatted in EXT2 / EXT3 (See Note above)
  • Press the power button on the front to restart with the new firmware


To Install a Full Web Interface Continue HERE


Note Note:

Some USB Flash / Disk Drives* are reported not to work, The reason for this is not fully understood, However the following Tips are known to help :-

  • Ensure no other USB devices are connected
  • Do not use a USB extender cable
  • Removing all other files / full-formatting can prevent file fragmentation
  • Try both USB ports (HDR)
  • Smaller capacity drives seem to work more successfully than large ones
  • Last Resort, Try a different USB Flash Drive