Difference between revisions of "Install Modified Firmware"

From hummy.tv Wiki
Jump to: navigation, search
(HD Fox T2)
(HD Fox T2)
Line 21: Line 21:
 
* Download the firmware and, if it is a zip file, extract it;
 
* Download the firmware and, if it is a zip file, extract it;
 
* Rename the resulting file as ''HD_FOX_T2_Upgrade.hdf'' and place it in the root of a FAT32 formatted USB Disk (flash or externally powered);
 
* Rename the resulting file as ''HD_FOX_T2_Upgrade.hdf'' and place it in the root of a FAT32 formatted USB Disk (flash or externally powered);
* Put the unit into standby using the remote, or power button on front;
+
* Put the unit into standby using the remote, or power button on the front;
 
* Plug the USB disk into the rear USB port, first unplugging any connected hard drive;
 
* Plug the USB disk into the rear USB port, first unplugging any connected hard drive;
 
* Turn on the TV and switch to the Humax input;
 
* Turn on the TV and switch to the Humax input;
* Press and hold down the power button on front until you see the software update begin, and the progress is shown on the TV screen. The initial ''download'' is very quick and then programming takes 2-3 minutes;
+
* Press and hold down the power button on the front until you see the software update begin, and the progress is shown on the TV screen. The initial ''download'' is very quick and then programming takes 2-3 minutes;
 
* When the update is complete End will appear on the front display and ''Success Downloading!'' will appear on the TV;
 
* When the update is complete End will appear on the front display and ''Success Downloading!'' will appear on the TV;
 
* Unplug the USB drive;
 
* Unplug the USB drive;
 
* Reconnect external hard drive;
 
* Reconnect external hard drive;
* Press the power button on front to restart with the new firmware.
+
* Press the power button on the front to restart with the new firmware.

Revision as of 11:10, 10 September 2011

The procedure for upgrading Humax software, (both original and modified) differs slighty for for the HDR and HD models. Please see the relevant section below.

Note Note: Some USB flash drives are reported not to work. If you have problems, ensure that you do not have a USB extension cable connected and try a different flash drive. On the HDR, priorities for scanning the USB ports vary depending on other connected devices so try both USB ports

HDR Fox T2

  • Download the firmware and, if it is a zip file, extract it;
  • Rename the resulting file as HDR_FOX_T2_Upgrade.hdf and place it in the root of a FAT32 formatted USB Disk (flash or externally powered);
  • Put the unit into standby using the remote or big button on the front;
  • Make sure that the unit has completely shut down by listening for the hard drive to power down (accompanied by a click);
  • Plug the USB disk into the front or rear USB port;
  • Turn on the TV and switch to the Humax input;
  • Start up the Humax using the big button on the front;
  • The software update should begin automatically and the progress shown on the TV screen. The initial download is very quick and then programming takes 2-3 minutes;
  • When the update is complete End will appear on the front display and Success Downloading! will appear on the TV;
  • Unplug the USB drive;
  • Press the big button on the front again to restart with the new firmware.

HD Fox T2

  • Download the firmware and, if it is a zip file, extract it;
  • Rename the resulting file as HD_FOX_T2_Upgrade.hdf and place it in the root of a FAT32 formatted USB Disk (flash or externally powered);
  • Put the unit into standby using the remote, or power button on the front;
  • Plug the USB disk into the rear USB port, first unplugging any connected hard drive;
  • Turn on the TV and switch to the Humax input;
  • Press and hold down the power button on the front until you see the software update begin, and the progress is shown on the TV screen. The initial download is very quick and then programming takes 2-3 minutes;
  • When the update is complete End will appear on the front display and Success Downloading! will appear on the TV;
  • Unplug the USB drive;
  • Reconnect external hard drive;
  • Press the power button on the front to restart with the new firmware.