Difference between revisions of "Remote Disassembled"
Ezra pound (talk | contribs) |
Ezra pound (talk | contribs) |
||
| Line 1: | Line 1: | ||
| − | [[File:rem00.png|400px|thumb|right|<<<--3------------------2-----------------Start Here]] | + | [[File:rem00.png|400px|thumb|right|'''<<<--3------------------2-----------------Start Here''']] |
| − | [[File:rem01.png|400px|thumb|right|Photo 2 | + | [[File:rem01.png|400px|thumb|right|'''Photo 2 - First 2 lugs 'popped'''']] |
| − | [[File:rem02.png|400px|thumb|right|Photo 3 | + | [[File:rem02.png|400px|thumb|right|'''Photo 3 - Battery end lugs''']] |
'''Background''' | '''Background''' | ||
| Line 15: | Line 15: | ||
'''Disassembly''' | '''Disassembly''' | ||
| − | Remove the batteries and replace the cover, The case is held together with 12 ‘snap fit | + | Remove the batteries and replace the cover, The case is held together with 12 ‘snap fit lug + Barbs’ (Photos 6 + 7), 5 on each long side and 2 at the battery end, The locations of the 5 side lugs are shown in Photo 1. The only tools required for the disassembly are two thin metal objects, I used two No. 22 scalpel blades (0.4mm thick), Although it is possible to use a thicker tool it will inevitably damage the case as the gap between the two halves of the case is very small. |
Locate a centre lug on a long side using photo 1 and insert a scapel blade at that point, leaver the bottom half of the case outwards and a ‘click’ should be heard as the barb disengages, Keep this scalpel in place while you work on the next lug towards the battery end, Do the same procedure on the second lug, Photo 2 shows two blades in place, It should be safe to remove the blades now. | Locate a centre lug on a long side using photo 1 and insert a scapel blade at that point, leaver the bottom half of the case outwards and a ‘click’ should be heard as the barb disengages, Keep this scalpel in place while you work on the next lug towards the battery end, Do the same procedure on the second lug, Photo 2 shows two blades in place, It should be safe to remove the blades now. | ||
| Line 27: | Line 27: | ||
Clean the PCB with Methylated Spirits and a cotton bud, the areas of interest are the ‘fingers’ as shown on PCB detail Photo 8 | Clean the PCB with Methylated Spirits and a cotton bud, the areas of interest are the ‘fingers’ as shown on PCB detail Photo 8 | ||
| − | Next use | + | Next use Methylated Spirits and a cotton bud to clean the round ‘Waffles’ on the underside of the buttons Photo 9 |
'''Re-Assembly''' | '''Re-Assembly''' | ||
| Line 35: | Line 35: | ||
{| border="1" | {| border="1" | ||
|- | |- | ||
| − | ![[File:rem05.png|400px|thumb|right|Photo 4 PCB under lug]] | + | ![[File:rem05.png|400px|thumb|right|Photo 4 - PCB under lug]] |
| − | ![[File:rem14.png|400px|thumb|right|Photo 5 Tools]] | + | ![[File:rem14.png|400px|thumb|right|Photo 5 - Tools]] |
|- | |- | ||
| − | ![[File:rem03.png|400px|thumb|right|Photo 6 | + | ![[File:rem03.png|400px|thumb|right|Photo 6 - 'Lug']] |
| − | ![[File:rem04.png|400px|thumb|right|Photo 7 'Barb']] | + | ![[File:rem04.png|400px|thumb|right|Photo 7 - 'Barb']] |
|- | |- | ||
| − | ![[File:rem07.png|400px|thumb|right| Photo 8 Fingers]] | + | ![[File:rem07.png|400px|thumb|right| Photo 8 - PCB Fingers]] |
| − | ![[File:rem09.png|400px|thumb|right|Photo 9 'Waffles']] | + | ![[File:rem09.png|400px|thumb|right|Photo 9 - Button 'Waffles']] |
|- | |- | ||
| − | ![[File:rem06.png|400px|thumb|right|Photo 10 Full PCB]] | + | ![[File:rem06.png|400px|thumb|right|Photo 10 - Full PCB]] |
| − | ![[File:rem08.png|400px|thumb|right|Photo 11 Rear of Buttons]] | + | ![[File:rem08.png|400px|thumb|right|Photo 11 - Rear of Buttons]] |
|- | |- | ||
| − | ![[File:rem12.png|400px|thumb|right|Photo 12 Battery side of PCB]] | + | ![[File:rem12.png|400px|thumb|right|Photo 12 - Battery side of PCB]] |
| − | ![[File:rem11.png|400px|thumb|right|Photo 13 Top side of Buttons]] | + | ![[File:rem11.png|400px|thumb|right|Photo 13 - Top side of Buttons]] |
|- | |- | ||
| − | ![[File:rem13.png|400px|thumb|right|Photo 14 Back of Case (Inner)]] | + | ![[File:rem13.png|400px|thumb|right|Photo 14 - Back of Case (Inner)]] |
| − | ![[File:rem10.png|400px|thumb|right|Photo 15 Top of case (Inner)]] | + | ![[File:rem10.png|400px|thumb|right|Photo 15 - Top of case (Inner)]] |
|} | |} | ||
Revision as of 15:43, 16 December 2011
Background
The RM-F04 Remote Control supplied with the Humax HDR FOX T2 and Humax HD FOX T2 may need disassembling for various reasons, The main reason being that the Remote becomes unresponsive to key presses, even with new batteries.
You may also be just curious as to what is inside, Users have been known to disassemble their products for this very reason
Warning
The RM-F04 Remote is not held together with screws, It is ‘Snapped’ together which make it quite difficult to take apart, It is not recommended that you dissasemble your Remote unless there is a very good reason, e.g. it has stopped working. There is a real possibility that the case could be damaged
Disassembly
Remove the batteries and replace the cover, The case is held together with 12 ‘snap fit lug + Barbs’ (Photos 6 + 7), 5 on each long side and 2 at the battery end, The locations of the 5 side lugs are shown in Photo 1. The only tools required for the disassembly are two thin metal objects, I used two No. 22 scalpel blades (0.4mm thick), Although it is possible to use a thicker tool it will inevitably damage the case as the gap between the two halves of the case is very small.
Locate a centre lug on a long side using photo 1 and insert a scapel blade at that point, leaver the bottom half of the case outwards and a ‘click’ should be heard as the barb disengages, Keep this scalpel in place while you work on the next lug towards the battery end, Do the same procedure on the second lug, Photo 2 shows two blades in place, It should be safe to remove the blades now.
Disengage the last side lug at the battery end, Now locate the battery end lug (Photo 3) nearest to the lugs already opened and open it, Followed by the second battery and lug.
Work up the other side of the case to the middle lug prizing the case apart as you go, Remove the last 4 lugs, NOTE there are no lugs on the other end but there is a hinge arrangement
With buttons facing down, remove the back of the remote, Remove the Printed Circuit Board by gently levering it away from the corner plastic lug (Photo 4)
Clean the PCB with Methylated Spirits and a cotton bud, the areas of interest are the ‘fingers’ as shown on PCB detail Photo 8
Next use Methylated Spirits and a cotton bud to clean the round ‘Waffles’ on the underside of the buttons Photo 9
Re-Assembly
Clip PCB back into place, Then Hook the two halves of the case back together at the non Battery end and then snap all other lugs into place
